Revision: Electricity Science English Medium Class 10 CBSE

Current is defined as the rate of flow of charge.

Substances whose resistance decreases tremendously with decreasing temperature and reaches nearly zero near absolute zero are called superconductors; e.g., lead, tin, etc.

 Semiconductors: Substances whose resistance decreases with the increase in temperature are named as semiconductors. E.g. manganin, constantan etc.

An electric current is measured by the amount of electric charge moving per unit time at any point in the circuit.

The magnitude of an electric current is the number of electric charges flowing through a conductor in one second.

Electromotive force: When no current is drawn from a cell, when the cell is in open circuit, the potential difference between the terminals of the cell is called its electromotive force (or e.m.f.).

The movement of the positive charge is called conventional current.

The unit of electric current is ampere (A). When 1 C of charge flows through a conductor in 1 s, it called 1 ampere (A) current.
I = `Q/t`

The resistivity of a material is the resistance of a wire of that material of unit length and unit area of cross-section.

A continuous and closed path of an electric current is called an electric circuit.

"Potential difference is the work done to move a unit charge from one point to another in an electric field."

One ohm is the resistance of a component when the potential difference of one volt applied across the component drives a current of one ampere through it.

The temperature coefficient is defined as the ratio of the increase in resistivity per degree rise in temperature to its resistivity at T₀.

The reciprocal of resistance is called conductllnce. It is denoted by the letter G. 

Current density is a vector quantity, often known as an area vector or cross-sectional area vector, whose value is equal to the electric current flowing per unit area.

J = `"I"/"A"`

S.I unit is A/m².

One coulomb is the amount of electric charge transferred by a current of one ampere in one second.

Electric fuse is a safety device which is used in household wiring and in many appliances.

The solution through which the electricity passes is called an electrolyte.

When a resistor is connected in an electrical circuit, heat is produced in it due to the current. This is known as the heating effect of current.

In an electrical circuit, electric power is defined as the rate at which electrical energy is supplied by the source.

Electric power (P) is the rate at which electrical energy is transferred or consumed in an electrical circuit.

Potential difference (V) between two points = Work done (W)/Charge (Q)
V = \[\frac {W}{Q}\]

The SI unit of electric potential difference is volt (V)

1 volt = \[\frac{1\mathrm{~joule}}{1\mathrm{~coulomb}}\] = 1 J C^-1

R ∝ \[\frac {1}{A}\]

or

R = ρ\[\frac {1}{A}\]

The SI unit of resistivity is Ω m.

Electric Power P = \[\frac {W}{t}\] = VI = \[\frac {V^2}{R}\] = I²R

According to Ohm’s law, the current flowing in a conductor is directly proportional to the potential difference across its ends, provided the physical conditions and temperature of the conductor remain constant.
No, it is not always true. E.g., Diode valve, junction diode, etc., do not obey Ohm’s law.

Statement: Ohm’s Law

"The electric current flowing through a conductor is directly proportional to the potential difference across its ends, provided the temperature and other physical conditions of the conductor remain constant."

Mathematically,

I ∝ V or V = I R

where:

• V = Potential difference (in volts)
• I = Current (in amperes)
• R = Resistance of the conductor (in ohms, Ω)

Explanation:

When two conductors at different electric potentials are joined by a metallic wire, electrons flow from the conductor at a lower potential (excess electrons) to the one at a higher potential (deficit of electrons). This movement of electrons results in an electric current.

• The current continues to flow until both conductors reach the same potential.
• For continuous current flow, a constant potential difference must be maintained across the ends of the conductor (e.g., using a battery or power supply).

Derivation / Mathematical Proof:

From Ohm’s Law:

I ∝ V ⇒ \[\frac {V}{I}\] = constant

This constant is defined as the resistance (R) of the conductor. Therefore,

V = I R   ---(1)

This is the mathematical form of Ohm’s Law.

Special Case:

If the current I = 1 A, then:

V = R

This implies that the resistance of a conductor is numerically equal to the potential difference across it when 1 ampere of current flows through it.

Conclusion:

Ohm's Law provides a fundamental relationship between voltage, current, and resistance in an electric circuit. It is widely used in the design and analysis of electrical and electronic systems.

• Electricity is a convenient and controllable form of energy widely used in homes, industries, schools, and hospitals.
• Electric current is produced when electric charges flow through a conductor, and it flows only through a closed, continuous electric circuit.
• A switch completes or breaks the circuit; when the circuit is broken, current stops flowing, and devices like bulbs do not glow.
• Electric current is the rate of flow of charge, given by the relation I = Q / t, where Q is charge and t is time.
• In metallic wires, electrons are the charge carriers, but by convention, current flows from the positive to the negative terminal, in the opposite direction to electron flow.

• In a parallel combination, the potential difference across each resistor is the same as that across the terminals of the battery.
• The total current in a parallel circuit is equal to the sum of the currents in the individual branches, and the equivalent resistance is less than the smallest resistance connected.

• Electrical power represents the rate at which electrical energy is supplied by the source in an electric circuit.
• The S.I. unit of electrical power is a watt (W), and larger units such as kilowatt, megawatt, and gigawatt are used for measuring higher power.