Advertisements
Advertisements
प्रश्न
Right or wrong sentence.
Increasing the current passing through the wire decreases the magnetic field intensity.
विकल्प
Right
Wrong
Advertisements
उत्तर
The given sentence is wrong.
Explanation:
The magnetic field intensity around a current-carrying wire is directly proportional to the amount of current passing through it (B ∝ I). Therefore, increasing the current will actually increase the strength of the magnetic field, not decrease it.
APPEARS IN
संबंधित प्रश्न
Draw a schematic diagram of a circuit consisting of a battery of three cells of 2 V each, a 5 Ω resistor, an 8 Ω resistor, and a 12 Ω resistor, and a plug key, all connected in series.
Draw circuit symbols for
fixed resistance
Draw circuit symbols for
a cell
Draw circuit symbols for
an open switch
How does the short circuit form?
Who will spend more electrical energy? 500 W TV Set in 30 mins, or 600 W heater in 20 mins?
Find the odd one out and justify it.
Fuse wire, M.C.B., Rubber Gloves, Generator
Two tungsten bulbs of power 50 W and 60 W work on 220 V potential difference. If they are connected in parallel, how much current will flow in the main conductor?
The following figure shows the symbols for components used in the accompanying electrical circuit. Place them at proper places and complete the circuit.
Which law can you prove with the help of above circuit?
Resistances R1, R2, R3 and R4 are connected as shown in the figure. S1 and S2 are two keys. Discuss the current flowing in the circuit in the following cases.
- Both S1 and S2 are closed.
- Both S1 and S2 are open.
- S1 is closed but S2 is open.
Draw a neat diagram showing a closed electric circuit.
Explain the following:
Closed circuit
In any electric circuit, when the switch is on and the current flows through it why do the wire, switches, bulb or devices become hot?
If you touch an electric wire carrying current you get a shock, but if on the same wire the birds sit they do not get any shock/current. Explain why?
Write scientific reason.
It is beneficial to carry electrical energy in AC form as it is carried over long distances.
The switch is used to close or open an electric circuit.
In the circuit shown, which switches (L,M or N) must be closed to light up the bulb?
In which of the following circuits are the bulb connected in series?
Higher Order Question
A student made a circuit by using an electric cell, a switch, a torch bulb (fitted in the bulb holder), and copper connecting wires. When he turned on the switch, the torch bulb did not glow at all. The student checked the circuit and found that all the wire connections were tight.
- What could be the possible reason for the torch bulb not glowing even when the circuit appears to be complete?
Study the three electric circuits below. Each of them has a glass rod (G), a steel rod (S), and a wooden rod (W).
In which of the electric circuits would the bulb not light up.
Three bulbs are connected end to end from the battery. This connection is called _______.
Assertion: People struck by lightning receive a severe electrical shock.
Reason: Lightning carries very high voltage.
Explain about domestic electric circuits. (circuit diagram not required)
In a circuit, if the key is in open (off) condition, then electricity will not flow.
In an electrical circuit two resistors of 2 Ω and 4 Ω respectively are connected in series to a 6 V battery. The heat dissipated by the 4 Ω resistor in 5 s will be
Draw a circuit diagram of an electric circuit containing a cell, a key, an ammeter, a resistor of 2 Ω in series with a combination of two resistors (4 Ω each) in parallel and a voltmeter across the parallel combination. Will the potential difference across the 2 Ω resistor be the same as that across the parallel combination of 4 Ω resistors? Give reason.
Observe the circuit given:
1. Would any of the bulbs glow when the switch is in the ‘OFF’ position?
2. What will be the order in which the bulbs A, B, and C will glow when the switch is moved to the ‘ON’ position?
Match the following
| 1. | Insulator | a. | Coulomb |
| 2. | Conductor | b. | Electric circuit |
| 3. | Closed path | c. | Copper |
| 4. | Electric charge | d. | Rubber |
What are the essential components of an electric circuit?
In the following arrangement shown in the following figure, the bulb will not glow if the ends A and B are connected with
A complete circuit is left on for several minutes, causing the connecting copper wire to become hot. As the temperature of the wire increases, the electrical resistance of the wire
Set up the circuit shown in Figure again. Move the key to ‘ON’ position and watch carefully in which direction the compass needle gets deflected. Switch ‘OFF’ the current. Now keeping rest of the circuit intact, reverse the connections at the terminal of the cell. Again switch ‘on’ the current. Note the direction in which the needle gets deflected. Think of an explanation.
