Advertisements
Advertisements
प्रश्न
How does the short circuit form?
Advertisements
उत्तर
A short circuit occurs when the live and neutral wires come into contact due to damaged insulation or a fault in an appliance. This causes a large current to flow.
APPEARS IN
संबंधित प्रश्न
Redraw the circuit of question 1, putting in an ammeter to measure the current through the resistors and a voltmeter to measure the potential difference across the 12 Ω resistors. What would be the readings in the ammeter and the voltmeter?
Draw circuit symbols for
a cell
Draw circuit symbols for
an open switch
Draw a circuit diagram to show how 3 bulbs can be lit from a battery so that 2 bulbs are controlled by the same switch the third bulb has its own switch.
Two tungsten bulbs of power 50 W and 60 W work on 220 V potential difference. If they are connected in parallel, how much current will flow in the main conductor?
Resistances R1, R2, R3 and R4 are connected as shown in the figure. S1 and S2 are two keys. Discuss the current flowing in the circuit in the following cases.
- Both S1 and S2 are closed.
- Both S1 and S2 are open.
- S1 is closed but S2 is open.
A battery is to be formed by joining 3 dry cells with connecting wires. Show how will you connect the wires by drawing a diagram.
Write the condition required for a circuit to be a closed circuit.
Answer the following question.
With the help of a suitable circuit diagram prove that the reciprocal of the equivalent resistance of a group of resistances joined in parallel is equal to the sum of the reciprocals of the individual resistances.
What do you understand by the closed electric circuit
Draw a neat diagram showing a closed electric circuit.
Draw a neat diagram showing a open electric circuit.
What is the potential difference?
How much is the potential difference between live and neutral wires?
______ is the device used to close or open an electric circuit.
In the circuit diagram below, 10 units of electric charge move past point x every second What is the current in the circuit ______.
Higher Order Question
A student made a circuit by using an electric cell, a switch, a torch bulb (fitted in the bulb holder), and copper connecting wires. When he turned on the switch, the torch bulb did not glow at all. The student checked the circuit and found that all the wire connections were tight.
- What could be the possible reason for the torch bulb not glowing even when the circuit appears to be complete?
Study the electric circuit below. Which of the following switches should be closed so that only two bulbs will light up
Which of the following a simple circuit must-have?
_____ has a thin metallic filament that melts and breaks the connection when the circuit is overheated.
Assertion: People struck by lightning receive a severe electrical shock.
Reason: Lightning carries very high voltage.
What is electric circuit?
Explain about domestic electric circuits. (circuit diagram not required)
Instead of metal wires, a jute string can be used to make a circuit.
The rate of flow of electric charges in a circuit is called ______.
In the following circuits (Figure), heat produced in the resistor or combination of resistors connected to a 12 V battery will be
 |
 |
 |
| (i) | (ii) | (iii) |
In an electrical circuit three incandescent bulbs A, B and C of rating 40 W, 60 W and 100 W respectively are connected in parallel to an electric source. Which of the following is likely to happen regarding their brightness?
In an electric circuit, the current starts from ______.
What are the essential components of an electric circuit?
In the following arrangement shown in the following figure, the bulb will not glow if the ends A and B are connected with
Paheli is running short of connecting wires. To complete an electric circuit, she may use a ______.
Will the bulb glow in the circuit shown in the following figure? Explain.
Overloading of electric circuits can lead to short-circuiting.
Name the device which is used to measure the strength of the electric current in an electric circuit.
