Advertisements
Advertisements
Question
Obtain an expression for the surface tension of a liquid by the capillary rise method.
Advertisements
Solution
Capillary rise by surface tension
Practical application of capillarity:
1. Due to capillary action, oil rises in the cotton within an earthen lamp. Likewise, sap raises from the roots of a plant to its leaves and branches.
2. Absorption of ink by blotting paper.
3. Capillary action is also essential for the tear fluid from the eye to drain constantly.
4. Cotton dresses are preferred in summer because cotton dresses have fine pores which act as capillaries for sweat.
Surface Tension by capillary rise method: The pressure difference across a curved liquid-air interface is the basic factor behind the rising up of water in a narrow tube (influence of gravity is ignored). The capillary rise is more dominant in the case of very fine tubes. But this phenomenon is the outcome of the force of surface tension. In order to arrive at a relation between the capillary rise (h) and surface tension (T), consider a capillary tube that is held vertically in a beaker containing water, the water rises in the capillary tube to a height of h due to surface tension.
The surface tension force FT, acts along the tangent at the point of contact downwards and its reaction force upwards. Surface tension T, it resolved into two components
(i) Horizontal component T sin θ and
(ii) Vertical component T cos θ acting upwards, all along the whole circumference of the meniscus Total upward force = (T cos θ) (2πr) = 2πrT cos θ
where θ is the angle of contact, r is the radius of the tube. Let ρ be the density of water and h be the height to which the liquid rises inside the tube. Then,
[the volume of liquid column in the tube, V] = [volume of the liquid column of radius r height h] + [volume of liquid of radius r and height r - Volume of the hemisphere of radius r]
V = `π"r"^2"h" + (π"r"^2 xx "r" - 2/3π"r"^3)`
V = `π"r"^2"h" + 1/3π"r"^3`
The upward force supports the weight of the liquid column above the free surface, therefore,
2πrT cos θ = `π"r"^2 ("h" + 1/3"r")ρ"g"`
T = `("r"("h" + 1/3"r")ρ"g")/(2 cos θ)`
If the capillary is a very fine tube of radius (i.e., the radius is very small) then `"r"/3` can be neglected when it is compared to the height h. Therefore,
T = `("r"ρ"gh")/(2 cos θ)`
Liquid rises through a height h
h = `(2 "T" cos θ)/("r"ρ"g") ⇒ "h" ∝ 1/"r"`
This implies that the capillary rise (h) is inversely proportional to the radius (r) of the tube, i. e., the smaller the radius of the tube greater will be the capillarity.
APPEARS IN
RELATED QUESTIONS
In which of the following substances, surface tension increases with increase in temperature ?
- Copper
- Molten copper
- Iron
- Molten iron
'n' droplets of equal size of radius r coalesce to form a bigger drop of radius R. The energy liberated is equal to...................
(T =Surface tension of water)
`(a) 4piR^2T[n^(1/3)-1]`
`(b) 4pir^2T[n^(1/3)-1]`
`(c) 4piR^2T[n^(2/3)-1]`
`(d)4 pir^2T[n^(2/3)-1]`
The force of surface tension acts tangentially to the surface whereas the force due to air pressure acts perpendicularly on the surface. How is then the force due to excess pressure inside a bubble balanced by the force due to the surface tension?
If water in one flask and castor oil in other are violently shaken and kept on a table, which will come to rest earlier?
The lower end of a capillary tube is immersed in mercury. The level of mercury in the tube is found to be 2 cm below the outer level. If the same tube is immersed in water, up to what height will the water rise in the capillary?
A capillary tube of radius 0.50 mm is dipped vertically in a pot of water. Find the difference between the pressure of the water in the tube 5.0 cm below the surface and the atmospheric pressure. Surface tension of water = 0.075 N m−1.
A cubical box is to be constructed with iron sheets 1 mm in thickness. What can be the minimum value of the external edge so that the cube does not sink in water? Density of iron = 8000 kg/m3 and density of water = 1000 kg/m3.
What is capillarity?
The free surface of oil in a tanker, at rest, is horizontal. If the tanker starts accelerating the free surface will be titled by an angle θ. If the acceleration is a ms–2, what will be the slope of the free surface?
Surface tension is exhibited by liquids due to force of attraction between molecules of the liquid. The surface tension decreases with increase in temperature and vanishes at boiling point. Given that the latent heat of vaporisation for water Lv = 540 k cal kg–1, the mechanical equivalent of heat J = 4.2 J cal–1, density of water ρw = 103 kg l–1, Avagadro’s No NA = 6.0 × 1026 k mole–1 and the molecular weight of water MA = 18 kg for 1 k mole.
- Estimate the energy required for one molecule of water to evaporate.
- Show that the inter–molecular distance for water is `d = [M_A/N_A xx 1/ρ_w]^(1/3)` and find its value.
- 1 g of water in the vapor state at 1 atm occupies 1601 cm3. Estimate the intermolecular distance at boiling point, in the vapour state.
- During vaporisation a molecule overcomes a force F, assumed constant, to go from an inter-molecular distance d to d ′. Estimate the value of F.
- Calculate F/d, which is a measure of the surface tension.
