Advertisements
Advertisements
प्रश्न
Define absolute error.
Advertisements
उत्तर
- For a given set of measurements of a quantity, the magnitude of the difference between mean value (Most probable value) and each individual value is called absolute error (Δa) in the measurement of that quantity.
- absolute error = |mean value - measured value|
Δa1 = |amean - a1|
Similarly,
Δa2 = |amean - a2|,
`\vdots \vdots \vdots`
Δan = |amean - an|
APPEARS IN
संबंधित प्रश्न
Define relative error.
Answer the following question.
Show that if Z = `"A"/"B"`, `(triangle"Z")/"Z" = (triangle"A")/"A" + (triangle "B")/"B"`
The masses of two bodies are measured to be 15.7 ± 0.2 kg and 27.3 ± 0.3 kg. What is the total mass of the two and the error in it?
In a workshop, a worker measures the length of a steel plate with Vernier calipers having a least count 0.01 cm. Four such measurements of the length yielded the following values: 3.11 cm, 3.13 cm, 3.14 cm, 3.14 cm. Find the mean length, the mean absolute error, and the percentage error in the measured value of the length.
In Ohm’s experiments, the values of the unknown resistances were found to be 6.12 Ω, 6.09 Ω, 6.22 Ω, 6.15 Ω. Calculate the (mean) absolute error, relative error, and percentage error in these measurements.
Solve the numerical example.
If the length of a cylinder is l = (4.00 ± 0.001) cm, radius r = (0.0250 ± 0.001) cm and mass m = (6.25 ± 0.01) g. Calculate the percentage error in the determination of density.
If Q = `"X"^"n"/"Y"^"m"` and Δx is absolute error in the measurement of X, Δy is absolute error in the measurement of Y, then absolute error ΔQ in Q is ______.
The relative density of a metal may be found by hanging a block of the metal from a spring balance and nothing that in air, the balance reads (5 .00 ± 0.05)N while in water, it reads (4.00 ± 0.05)N. The relative density would be quoted as ______.
You measure two quantities as A = 1.0 m ± 0.2 m, B = 2.0 m ± 0.2 m. We should report correct value for `sqrt(AB)` as ______.
The mean length of an object is 5 cm. Which of the following measurements is most accurate?
A physical quantity X is related to four measurable quantities a, b, c and d as follows: X = a2 b3 c5/2d–2. The percentage error in the measurement of a, b, c and d are 1%, 2%, 3% and 4%, respectively. What is the percentage error in quantity X? If the value of X calculated on the basis of the above relation is 2.763, to what value should you round off the result.
The dependence of g on geographical latitude at sea level is given by `g = g_0(1 + betasin^2Phi)` where Φ is the latitude angle and β is a dimensionless constant. If Δg is the error in the measurement of g then the error in measurement of latitude angle is ______.
A travelling microscope is used to determine the refractive index of a glass slab. If 40 divisions are there in 1 cm on main scale and 50 Vernier scale divisions are equal to 49 main scale divisions, then least count of the travelling microscope is ______ × 10-6 m.
The least count of the main scale of a screw gauge is 1 mm. The minimun number of divisions on its circular scale required to measure 5 µm diameter of a wire is ______.
Which statement best describes the effect of systematic errors on measurements?
A laboratory balance shows a mass reading even when no object is placed on the pan. What is the main cause of this error?
What are random errors?
A weighing scale that always reads a constant +0.2 kg because its zero mark is misaligned is a clear example of a(n):
A student reads a measuring cylinder from above the liquid level, causing the reading to be higher than the actual value. What type of error is this?
Which one of the following is an effective way to reduce systematic errors in an experiment?
If the pointer of the voltmeter is not exactly at the zero of the scale, then the error is called ______.
Instrumental error can be minimised by ______.
Error due to non-removal of parallax between pointer and its image in case of magnetic compass needle causes ______.
