Advertisements
Advertisements
प्रश्न
Find the percentage error in kinetic energy of a body having mass 60.0 ± 0.3 g moving with a velocity of 25.0 ± 0.1 cm/s.
Advertisements
उत्तर
Given: m = 60.0 g, v = 25.0 cm/s, Δm = 0.3 g, Δv = 0.1 cm/s
To find: Percentage error in K.E.
Formula: K.E. = `1/2` mv2
Calculation: K.E. = `1/2 "mv"^2`
= `(Delta "K.E.")/("K.E.") xx 100`
`= ((triangle"m")/"m" + (2 * triangle"v")/"v") xx 100%`
= `(0.3/60.0 + (2 xx 0.1)/25.0) xx 100%`
= 1.3 %
The percentage error in kinetic energy is 1.3%.
APPEARS IN
संबंधित प्रश्न
Define absolute error.
Define Mean absolute error.
Define relative error.
In a workshop, a worker measures the length of a steel plate with Vernier calipers having a least count 0.01 cm. Four such measurements of the length yielded the following values: 3.11 cm, 3.13 cm, 3.14 cm, 3.14 cm. Find the mean length, the mean absolute error, and the percentage error in the measured value of the length.
In Ohm’s experiments, the values of the unknown resistances were found to be 6.12 Ω, 6.09 Ω, 6.22 Ω, 6.15 Ω. Calculate the (mean) absolute error, relative error, and percentage error in these measurements.
Solve the numerical example.
If the length of a cylinder is l = (4.00 ± 0.001) cm, radius r = (0.0250 ± 0.001) cm and mass m = (6.25 ± 0.01) g. Calculate the percentage error in the determination of density.
Solve the numerical example.
If the formula for a physical quantity is X = `("a"^4"b"^3)/("c"^(1//3)"d"^(1//2))` and if the percentage error in the measurements of a, b, c and d are 2%, 3%, 3% and 4% respectively. Calculate percentage error in X.
In an experiment, the percentage of error occurred in the measurement of physical quantities A, B, C and D are 1%, 2%, 3% and 4% respectively. Then the maximum percentage of error in the measurement X, where X = `(A^2B^(1/2))/(C^(1/3)D^3)`, will be:
The relative density of a metal may be found by hanging a block of the metal from a spring balance and nothing that in air, the balance reads (5 .00 ± 0.05)N while in water, it reads (4.00 ± 0.05)N. The relative density would be quoted as ______.
Measure of two quantities along with the precision of respective measuring instrument is A = 2.5 ms–1 ± 0.5 ms–1 B = 0.10 s ± 0.01 s. The value of A B will be ______.
You measure two quantities as A = 1.0 m ± 0.2 m, B = 2.0 m ± 0.2 m. We should report correct value for `sqrt(AB)` as ______.
Time for 20 oscillations of a pendulum is measured as t1 = 39.6 s; t2 = 39.9 s; t3 = 39.5 s. What is the precision in the measurements? What is the accuracy of the measurement?
The resistance R = `"V"/"I"`, where V = (50 ± 2) V and I = (20 ± 0.2)A. The percentage error in R is 'x' %.
The value of x to the nearest integer is ______.
In a Screw Gauge, the fifth division of the circular scale coincides with the reference line when the ratchet is closed. There are 50 divisions on the circular scale, and the main scale moves by 0.5 mm on a complete rotation. For a particular observation, the reading on the main scale is 5 mm and the 20th division of the circular scale coincides with the reference line. Calculate the true reading.
If E, L, M, and G denote the quantities as energy, angular momentum, mass, and constant of gravitation respectively, then the dimensions of P in the formula P = EL2M−5G−2 are ______.
A travelling microscope has 20 divisions per cm on the main scale while its Vernier scale has total 50 divisions and 25 Vernier scale divisions are equal to 24 main scale divisions, what is the least count of the travelling microscope?
If the zero of the vernier lies on the right-hand side and the fourth division coincides with the main scale division when the jaws are in contact so the correction will be ______.
A thermometer always reads 2°C higher than the actual temperature because its zero mark is incorrect. What type of error is this?
Which statement best describes the effect of systematic errors on measurements?
A laboratory balance shows a mass reading even when no object is placed on the pan. What is the main cause of this error?
A student reads a measuring cylinder from above the liquid level, causing the reading to be higher than the actual value. What type of error is this?
Which one of the following is an effective way to reduce systematic errors in an experiment?
Zero error of an instrument introduces ______.
Constant error can be caused due to ______.
