Advertisements
Advertisements
प्रश्न
The error in the measurement of the sides of a rectangle is 1%. The error in the measurement of its area is ______.
विकल्प
1%
`(1//2)`%
2%
None of the above
Advertisements
उत्तर
The error in the measurement of the sides of a rectangle is 1%. The error in the measurement of its area is 2%.
Explanation:
A = l × b
∴ `(triangle"A")/"A" = (trianglel)/l + (triangle "b")/"b"` = 1% + 1% = 2
APPEARS IN
संबंधित प्रश्न
Answer the following question.
Show that if Z = `"A"/"B"`, `(triangle"Z")/"Z" = (triangle"A")/"A" + (triangle "B")/"B"`
The masses of two bodies are measured to be 15.7 ± 0.2 kg and 27.3 ± 0.3 kg. What is the total mass of the two and the error in it?
The distance travelled by an object in time (100 ± 1)s is (5.2 ± 0.1) m. What are the speed and its maximum relative error?
In a workshop, a worker measures the length of a steel plate with Vernier calipers having a least count 0.01 cm. Four such measurements of the length yielded the following values: 3.11 cm, 3.13 cm, 3.14 cm, 3.14 cm. Find the mean length, the mean absolute error, and the percentage error in the measured value of the length.
In Ohm’s experiments, the values of the unknown resistances were found to be 6.12 Ω, 6.09 Ω, 6.22 Ω, 6.15 Ω. Calculate the (mean) absolute error, relative error, and percentage error in these measurements.
Solve the numerical example.
If the length of a cylinder is l = (4.00 ± 0.001) cm, radius r = (0.0250 ± 0.001) cm and mass m = (6.25 ± 0.01) g. Calculate the percentage error in the determination of density.
Solve the numerical example.
If the formula for a physical quantity is X = `("a"^4"b"^3)/("c"^(1//3)"d"^(1//2))` and if the percentage error in the measurements of a, b, c and d are 2%, 3%, 3% and 4% respectively. Calculate percentage error in X.
In an experiment, the percentage of error occurred in the measurement of physical quantities A, B, C and D are 1%, 2%, 3% and 4% respectively. Then the maximum percentage of error in the measurement X, where X = `(A^2B^(1/2))/(C^(1/3)D^3)`, will be:
If Q = `"X"^"n"/"Y"^"m"` and Δx is absolute error in the measurement of X, Δy is absolute error in the measurement of Y, then absolute error ΔQ in Q is ______.
The relative density of a metal may be found by hanging a block of the metal from a spring balance and nothing that in air, the balance reads (5 .00 ± 0.05)N while in water, it reads (4.00 ± 0.05)N. The relative density would be quoted as ______.
You measure two quantities as A = 1.0 m ± 0.2 m, B = 2.0 m ± 0.2 m. We should report correct value for `sqrt(AB)` as ______.
A physical quantity X is related to four measurable quantities a, b, c and d as follows: X = a2 b3 c5/2d–2. The percentage error in the measurement of a, b, c and d are 1%, 2%, 3% and 4%, respectively. What is the percentage error in quantity X? If the value of X calculated on the basis of the above relation is 2.763, to what value should you round off the result.
The dependence of g on geographical latitude at sea level is given by `g = g_0(1 + betasin^2Phi)` where Φ is the latitude angle and β is a dimensionless constant. If Δg is the error in the measurement of g then the error in measurement of latitude angle is ______.
A travelling microscope has 20 divisions per cm on the main scale while its Vernier scale has total 50 divisions and 25 Vernier scale divisions are equal to 24 main scale divisions, what is the least count of the travelling microscope?
A travelling microscope is used to determine the refractive index of a glass slab. If 40 divisions are there in 1 cm on main scale and 50 Vernier scale divisions are equal to 49 main scale divisions, then least count of the travelling microscope is ______ × 10-6 m.
The least count of the main scale of a screw gauge is 1 mm. The minimun number of divisions on its circular scale required to measure 5 µm diameter of a wire is ______.
A thermometer always reads 2°C higher than the actual temperature because its zero mark is incorrect. What type of error is this?
Which statement best describes the effect of systematic errors on measurements?
A laboratory balance shows a mass reading even when no object is placed on the pan. What is the main cause of this error?
What are random errors?
Which one of the following is an effective way to reduce systematic errors in an experiment?
Instrumental error can be minimised by ______.
Error due to non-removal of parallax between pointer and its image in case of magnetic compass needle causes ______.
The reason behind holding thermometer in the mouth instead of the armpit is to reduce ______.
Constant error can be caused due to ______.
