Advertisements
Advertisements
प्रश्न
A metal block of heat capacity 80 J°C−1 placed in a room at 20°C is heated electrically. The heater is switched off when the temperature reaches 30°C. The temperature of the block rises at the rate of 2°C s−1 just after the heater is switched on and falls at the rate of 0.2°C s−1 just after the heater is switched off. Assume Newton's law of cooling to hold.
- Find the power of the heater.
- Find the power radiated by the block just after the heater is switched off.
- Find the power radiated by the block when the temperature of the block is 25°C.
- Assuming that the power radiated at 25°C represents the average value in the heating process, find the time for which the heater was kept on.
Advertisements
उत्तर
Given:
Heat capacity of the metal block, s = 80 J°C−1
Heat absorb by the metal block is,
`H = s xx DeltaT = 80xx(30-10) = 800 J`
Rate of rise in tempreature of the block `= ((d theta)/(dt))=2^circC//s`
Rate of fall in temperature of the block = `((d theta)/(dt)) = - 0.2^circ C//s`
The negative sign indicates that the temperature is falling with time.
a. Energy = s `(Delta theta)`
(Power = Energy per unit time
∴ Power of the heater = Heat capacity ×`(d theta)/(dt)`
P = 80 × 2
P = 160 w
b. Power Radiated = Energy lost per unit time.
∴ P = heat capacity ×`((d theta)/(dt))`
Here, `(d theta)/(dt)` represents the rate of decrease in temperature.
p = 80 × 0.2
p = 16 W
c. 16 W of power is radiated when the temperature of the block decreases from 30°C to 20°C.
∴ `s xx ((d theta)/(dt))_{dec} = k (theta - theta_0)`
⇒ 16 = K (30 − 20)
K = 1.6
From newton's law of cooling,
∴ s`(d theta)/(dt) = K (theta - theta_0)`
`⇒ s(d theta)/(dt) = 1.6 (30 - 25)`
`⇒ s(d theta)/(dt) = 1.6 xx 5`
`⇒ s(d theta)/(dt) = 8 "Watt"`
d. As we know, that power given by the heater is P = 160 W
now we can use energy equations
Energy given by heater = Heat absorbed by block + heat loss
160t = 80(30 − 20) + 8t
154t = 800
t = 5.19 s
APPEARS IN
संबंधित प्रश्न
A copper block of mass 2.5 kg is heated in a furnace to a temperature of 500 °C and then placed on a large ice block. What is the maximum amount of ice that can melt? (Specific heat of copper = 0.39 J g–1 K–1; heat of fusion of water = 335 J g–1).
Answer the following question based on the P-T phase diagram of carbon dioxide:
Is CO2 solid, liquid or gas at
- –70 °C under 1 atm,
- –60 °C under 10 atm,
- 15 °C under 56 atm?
Answer the following questions based on the P–T phase diagram of CO2:
CO2 at 1 atm pressure and temperature – 60 °C is compressed isothermally. Does it go through a liquid phase?
Answer the following questions based on the P–T phase diagram of CO2:
Describe qualitatively the changes in a given mass of solid CO2 at 10 atm pressure and temperature –65 °C as it is heated up to room temperature at constant pressure.
Answer the following questions based on the P–T phase diagram of CO2:
CO2 is heated to a temperature 70 °C and compressed isothermally. What changes in its properties do you expect to observe?
A brass boiler has a base area of 0.15 m2 and thickness 1.0 cm. It boils water at the rate of 6.0 kg/min when placed on a gas stove. Estimate the temperature of the part of the flame in contact with the boiler. The thermal conductivity of brass = 109 J s –1 m–1 K–1; Heat of vaporisation of water = 2256 × 103 J kg–1.
Explain why a body with large reflectivity is a poor emitter
Answer the following question based on the P-T phase diagram of carbon dioxide:
At what temperature and pressure can the solid, liquid and vapour phases of CO2 co-exist in equilibrium?
Answer the following question based on the P-T phase diagram of carbon dioxide:
What is the effect of decrease of pressure on the fusion and boiling point of CO2?
Mark the correct options:
- A system X is in thermal equilibrium with Y but not with Z. System Y and Z may be in thermal equilibrium with each other.
- A system X is in thermal equilibrium with Y but not with Z. Systems Y and Z are not in thermal equilibrium with each other.
- A system X is neither in thermal equilibrium with Y nor with Z. The systems Y and Z must be in thermal equilibrium with each other.
- A system X is neither in thermal equilibrium with Y nor with Z. The system Y and Z may be in thermal equilibrium with each other.
During summers in India, one of the common practice to keep cool is to make ice balls of crushed ice, dip it in flavoured sugar syrup and sip it. For this a stick is inserted into crushed ice and is squeezed in the palm to make it into the ball. Equivalently in winter, in those areas where it snows, people make snow balls and throw around. Explain the formation of ball out of crushed ice or snow in the light of P–T diagram of water.
Latent heat of a substance is best defined as ______.
What happens to temperature at 0°C during melting of ice?
Effect of increasing external pressure on boiling point ______.
In a heating curve of ice and water, which part represents the latent heat of fusion?
Which statement best explains why the temperature of boiling water remains constant at 100°C until all the water has changed to steam (at 1 atm)?
Why is the latent heat of vaporisation much greater than the latent heat of fusion?
