Advertisements
Advertisements
प्रश्न
100 g of water is supercooled to –10°C. At this point, due to some disturbance mechanised or otherwise some of it suddenly freezes to ice. What will be the temperature of the resultant mixture and how much mass would freeze?
`[S_w = 1cal/g/^circC and L_(Fusion)^w = 80cal/g]`
Advertisements
उत्तर
According to the problem, the mass of water (m) = 100 g
Change in temperature ΔT = `0 - (-10) = 10^circC`
Specific heat of water (Sw) = 1 cal/g/°C
Latent heat of fusion of water `L_(fusion)^w` = 80 cal/g
Amount of heat required to change the temperature of 100 g of water at – 10°C to 0°C,
`Q = mS_wΔT`
= `100 xx 1 xx [0 - (- 10)]`
= 1000 cal
Let m gram of ice be melted.
∴ `Q = mL`
or `m = Q/L = 1000/80` = 12.5 g
As a small mass of ice is melted, thus the temperature of the resultant mixture will remain 0°C which contains 12.5 g of ice and 87.5 g of water.
APPEARS IN
संबंधित प्रश्न
A copper block of mass 2.5 kg is heated in a furnace to a temperature of 500 °C and then placed on a large ice block. What is the maximum amount of ice that can melt? (Specific heat of copper = 0.39 J g–1 K–1; heat of fusion of water = 335 J g–1).
Answer the following question based on the P-T phase diagram of carbon dioxide:
Is CO2 solid, liquid or gas at
- –70 °C under 1 atm,
- –60 °C under 10 atm,
- 15 °C under 56 atm?
Answer the following questions based on the P–T phase diagram of CO2:
Describe qualitatively the changes in a given mass of solid CO2 at 10 atm pressure and temperature –65 °C as it is heated up to room temperature at constant pressure.
Answer the following questions based on the P–T phase diagram of CO2:
Describe qualitatively the changes in a given mass of solid CO2 at 10 atm pressure and temperature –65 °C as it is heated up to room temperature at constant pressure.
Answer the following questions based on the P–T phase diagram of CO2:
CO2 is heated to a temperature 70 °C and compressed isothermally. What changes in its properties do you expect to observe?
A brass boiler has a base area of 0.15 m2 and thickness 1.0 cm. It boils water at the rate of 6.0 kg/min when placed on a gas stove. Estimate the temperature of the part of the flame in contact with the boiler. The thermal conductivity of brass = 109 J s –1 m–1 K–1; Heat of vaporisation of water = 2256 × 103 J kg–1.
Explain why a body with large reflectivity is a poor emitter
Answer the following question based on the P-T phase diagram of carbon dioxide:
At what temperature and pressure can the solid, liquid and vapour phases of CO2 co-exist in equilibrium?
Answer the following question based on the P-T phase diagram of carbon dioxide:
What is the effect of decrease of pressure on the fusion and boiling point of CO2?
Answer the following question based on the P-T phase diagram of carbon dioxide:
What are the critical temperature and pressure for CO2? What is their significance?
Mark the correct options:
- A system X is in thermal equilibrium with Y but not with Z. System Y and Z may be in thermal equilibrium with each other.
- A system X is in thermal equilibrium with Y but not with Z. Systems Y and Z are not in thermal equilibrium with each other.
- A system X is neither in thermal equilibrium with Y nor with Z. The systems Y and Z must be in thermal equilibrium with each other.
- A system X is neither in thermal equilibrium with Y nor with Z. The system Y and Z may be in thermal equilibrium with each other.
During summers in India, one of the common practice to keep cool is to make ice balls of crushed ice, dip it in flavoured sugar syrup and sip it. For this a stick is inserted into crushed ice and is squeezed in the palm to make it into the ball. Equivalently in winter, in those areas where it snows, people make snow balls and throw around. Explain the formation of ball out of crushed ice or snow in the light of P–T diagram of water.
Latent heat of a substance is best defined as:
Relation between heat Q, mass mmm, and specific latent heat L:
What happens to temperature at 0°C during melting of ice?
Effect of increasing external pressure on boiling point:
