Advertisements
Advertisements
प्रश्न
A modulating signal is a square wave, as shown
The carrier wave is given by `c(t) = 2 sin (8pit) "volts"`
(i) Sketch the amplitude modulated waveform
(ii) What is the modulation index?
Advertisements
उत्तर
It can be observed from the given modulating signal that the amplitude of the modulating signal, Am = 1 V
It is given that the carrier wave c (t) = 2 sin (8πt)
∴Amplitude of the carrier wave, Ac = 2 V
Time period of the modulating signal Tm = 1 s
The angular frequency of the modulating signal is calculated as:
`omega_m = 2pi/T_m`
`= 2pi "rad" s^(-1)` ... (1)
The angular frequency of the carrier signal is calculated as:
`omega_c = 8pi "rad" s^(-1)` ... (ii)
From equations (i) and (ii), we get:
`mega_c = 4omega_m`
The amplitude modulated waveform of the modulating signal is shown in the following figure.
(ii)Modulation index, `m = A_m/A_c = 1/2 = 0.5`
संबंधित प्रश्न
A signal of 5 kHz frequency is amplitude modulated on a carrier wave of frequency 2 MHz. What are the frequencies of the side bands produced?
Draw a block diagram of a detector for AM signal and show, using necessary processes and the waveforms, how the original message signal is detected from the input AM wave.
Explain the process of amplitude modulation.
For an amplitude modulated wave, the maximum amplitude is found to be 10 V while the minimum amplitude is found to be 2 V. Determine the modulation index μ. What would be the value of μ if the minimum amplitude is zero volt?
The frequencies of two side bands in an AM wave are 640 kHz and 660 kHz respectively. Find the frequencies of carrier and modulating signal. What is the bandwidth required for amplitude modulation?
Define the term 'amplitude modulation'
Explain any two factors which justify the need for modulating a low frequency base-band signal.
Write two advantages of frequency modulation over amplitude modulation.
Why is frequency modulation preferred over amplitude modulation for transmission of music?
A message signal of frequency ωm is superposed on a carrier wave of frequency ωc to get an amplitude modulated wave (AM). The frequency of the AM wave will be ______.
Identify the mathematical expression for amplitude modulated wave ______.
In amplitude modulation, the modulation index m, is kept less than or equal to 1 because ______.
- m > 1, will result in interference between carrier frequency and message frequency, resulting into distortion.
- m > 1 will result in overlapping of both side bands resulting into loss of information.
- m > 1 will result in change in phase between carrier signal and message signal.
- m > 1 indicates amplitude of message signal greater than amplitude of carrier signal resulting into distortion.
Compute the LC product of a tuned amplifier circuit required to generate a carrier wave of 1 MHz for amplitude modulation.
Why is a AM signal likely to be more noisy than a FM signal upon transmission through a channel?
On radiating (sending out) an AM modulated signal, the total radiated power is due to energy carried by ωc, ωc – ωm and ωc + ωm. Suggest ways to minimise cost of radiation without compromising on information.
An amplitude modulated wave is as shown in figure. Calculate
- the percentage modulation
- peak carrier voltage and
- peak value of information voltage.
The maximum and minimum voltage of an amplitude modulated signal are 60 V and 20 V respectively. The percentage modulation index will be ______.
The maximum amplitude for an amplitude modulated wave is found to be 12V while the minimum amplitude is found to be 3V. The modulation index is 0.6x where x is ______.
A signal of 5 kHz frequency is amplitude modulated on a carrier wave of frequency 2 MHz. The frequencies of the resultant signal are ______.
