Advertisements
Advertisements
प्रश्न
Two wires of diameter 0.25 cm, one made of steel and the other made of brass are loaded as shown in Fig. 9.13. The unloaded length of steel wire is 1.5 m and that of brass wire is 1.0 m. Compute the elongations of the steel and the brass wires.
Advertisements
उत्तर १
Elongation of the steel wire = 1.49 × 10–4 m
Elongation of the brass wire = 1.3 × 10–4 m
Diameter of the wires, d = 0.25 m
Hence, the radius of the wires, `r=d/2` = 0.125 cm
Length of the steel wire, L1 = 1.5 m
Length of the brass wire, L2 = 1.0 m
Total force exerted on the steel wire:
F1 = (4 + 6) g = 10 × 9.8 = 98 N
Young’s modulus for steel:
`Y_1 = (F_1/A_1)/(triangleL_1/L_1)`
Where,
ΔL1 = Change in the length of the steel wire
A1 = Area of cross-section of the steel wire = `pir_1^2`
Young’s modulus of steel, Y1 = 2.0 × 1011 Pa
`:.triangleL_1 = (F_1xxL_1)/(A_1xxY_1) = (F_1xxL_1)/(pir_1^2xxY_1)`
`= (98xx1.5)/(pi(0.125 xx 10^(-2))^2 xx 2 xx 10^11) = 1.49 xx 10^(-4)m`
Total force on the brass wire:
F2 = 6 × 9.8 = 58.8 N
Young’s modulus for brass: `Y_2 = (F_2/A_2)/((triangleL_2)/L_2)`
Where
`triangleL_2` = change in length
`A_2` = Area of cross-section of the brass wire
`:.triangleL_2 = (F_2xxL_2)/(a_2xxY_2) = (F_2xx L_2)/(pir_2^2 xx Y_2)`
`= (58.8 xx 1.0)/(pixx(0.125xx10^(-2))^2 xx (0.91xx10^(11))) = 1.3xx10^(-4)m`
Elongation of the steel wire = 1.49 × 10–4 m
Elongation of the brass wire = 1.3 × 10–4 m
उत्तर २
For steel wire total force on steel wire
F1 = 4+6 = 10 kg f = 10 x 9.8 N
l1 = 1.5 m, Δl1 = ?; 2r1 = 0.25 cm
or `r_1 = (0.25)/2 cm = 0.125xx 10^(-2) m`
`Y_1 = 2.0 xx 10^11` Pa
For brass wire, F2 = 6.0 kg f = 6 x 9.8 N
2r2 = 0.25 cm
or `r_2 = (0.25/2) = 0.125 xx 10^(-2) m`
`Y_2 = 0.91 xx 10^11 Pa`, `l_2 = 1.0 m` `trianglel_2 = ?`
Since` Y_1 = (F_1xxl_1)/(A_1xxtrianglel_1) = (F_1xxl_2)/(pir_1^2 xx trianglel_1) => trianglel_1 = (F_1xxl_1)/(pir_1^2xxtrianglel_1)`
or `trianglel_1 = ((10xx9.8)xx1.5xx7)/(22xx(0.125xx10^(-2))^2xx2xx10^11) = 1.49 xx 10^(-4) m`
And `trianglel_2 = (F_2xxl_2)/(pir_2^2 xx Y_2) = ((6xx9.8)xx1xx7)/(22xx(0.125xx10^(-2))^2xx(0.91xx10^11)) = 1.3 xx 10^(-4) m`
APPEARS IN
संबंधित प्रश्न
Four identical hollow cylindrical columns of mild steel support a big structure of mass 50,000 kg. The inner and outer radii of each column are 30 cm and 60 cm respectively. Assuming the load distribution to be uniform, calculate the compressional strain of each column.
A steel rod of cross-sectional area 4 cm2 and 2 m shrinks by 0.1 cm as the temperature decreases in night. If the rod is clamped at both ends during the day hours, find the tension developed in it during night hours. Young modulus of steel = 1.9 × 1011 N m−2.
A copper wire of cross-sectional area 0.01 cm2 is under a tension of 20N. Find the decrease in the cross-sectional area. Young modulus of copper = 1.1 × 1011 N m−2 and Poisson ratio = 0.32.
`["Hint" : (Delta"A")/"A"=2(Delta"r")/"r"]`
Young's modulus of a perfectly rigid body is ______.
The temperature of a wire is doubled. The Young’s modulus of elasticity ______.
A steel rod (Y = 2.0 × 1011 Nm–2; and α = 10–50 C–1) of length 1 m and area of cross-section 1 cm2 is heated from 0°C to 200°C, without being allowed to extend or bend. What is the tension produced in the rod?
If the yield strength of steel is 2.5 × 108 Nm–2, what is the maximum weight that can be hung at the lower end of the wire?
A steel rod of length 2l, cross sectional area A and mass M is set rotating in a horizontal plane about an axis passing through the centre. If Y is the Young’s modulus for steel, find the extension in the length of the rod. (Assume the rod is uniform.)
In nature, the failure of structural members usually result from large torque because of twisting or bending rather than due to tensile or compressive strains. This process of structural breakdown is called buckling and in cases of tall cylindrical structures like trees, the torque is caused by its own weight bending the structure. Thus the vertical through the centre of gravity does not fall within the base. The elastic torque caused because of this bending about the central axis of the tree is given by `(Ypir^4)/(4R) . Y` is the Young’s modulus, r is the radius of the trunk and R is the radius of curvature of the bent surface along the height of the tree containing the centre of gravity (the neutral surface). Estimate the critical height of a tree for a given radius of the trunk.
A metal wire of length L, area of cross section A and Young's modulus Y behaves as a spring of spring constant k given by:
A boy's catapult is made of rubber cord which is 42 cm long, with a 6 mm diameter of cross-section and negligible mass. The boy keeps a stone weighing 0.02 kg on it and stretches the cord by 20 cm by applying a constant force. When released, the stone flies off with a velocity of 20 ms-1. Neglect the change in the area of the cross-section of the cord while stretched. Young's modulus of rubber is closest to ______.
The force required to stretch a wire of cross section 1 cm2 to double its length will be ______.
(Given Young's modulus of the wire = 2 × 1011 N/m2)
Young's modulus is also known as ______.
What is longitudinal strain?
Which of the following statements about Young's modulus is correct?
In the formula Y = MgL/(πr²l), what does 'l' represent?
The maximum elongation of a steel wire of 1 m length if the elastic limit of steel and its Young’s modulus, respectively, are 8 × 108 Nm−2 and 2 × 1011 Nm−2, is ______.
