Advertisements
Advertisements
प्रश्न
The vernier scale of a travelling microscope has 50 divisions which coincide with 49 main scale divisions. If each main scale division is 0.5 mm, calculate the minimum inaccuracy in the measurement of distance.
Advertisements
उत्तर
A Diagram of the vernier calliper is shown below.
According to the problem, 50 divisions of the Vernier scale coincide with 49 main scale divisions.
50 VSD = 49 MSD
⇒ 1 MSD = `50/49` VSD or 1 VSD = `49/50` MSD
Where MSD = Main scale division and VSD = Vernier scale division.
We know that
Minimum inaccuracy = Vernier constant
= 1 MSD – 1 VSD
= 1 MSD – `49/50` MSD = `1/50` MSD
It is given in the problem that 1 MSD = 0.5 mm
Hence, minimum inaccuracy = `1/50 xx 0.5` mm = `1/100` = 0.01 mm
APPEARS IN
संबंधित प्रश्न
Define absolute error.
Define relative error.
If the measured values of the two quantities are A ± ΔA and B ± ΔB, ΔA and ΔB being the mean absolute errors. What is the maximum possible error in A ± B? Show that if Z = `"A"/"B"`
`(Delta "Z")/"Z" = (Delta "A")/"A" + (Delta "B")/"B"`
Solve the numerical example.
If the formula for a physical quantity is X = `("a"^4"b"^3)/("c"^(1//3)"d"^(1//2))` and if the percentage error in the measurements of a, b, c and d are 2%, 3%, 3% and 4% respectively. Calculate percentage error in X.
In an experiment, the percentage of error occurred in the measurement of physical quantities A, B, C and D are 1%, 2%, 3% and 4% respectively. Then the maximum percentage of error in the measurement X, where X = `(A^2B^(1/2))/(C^(1/3)D^3)`, will be:
If Q = `"X"^"n"/"Y"^"m"` and Δx is absolute error in the measurement of X, Δy is absolute error in the measurement of Y, then absolute error ΔQ in Q is ______.
The relative density of a metal may be found by hanging a block of the metal from a spring balance and nothing that in air, the balance reads (5 .00 ± 0.05)N while in water, it reads (4.00 ± 0.05)N. The relative density would be quoted as ______.
Measure of two quantities along with the precision of respective measuring instrument is A = 2.5 ms–1 ± 0.5 ms–1 B = 0.10 s ± 0.01 s. The value of A B will be ______.
You measure two quantities as A = 1.0 m ± 0.2 m, B = 2.0 m ± 0.2 m. We should report correct value for `sqrt(AB)` as ______.
A physical quantity X is related to four measurable quantities a, b, c and d as follows: X = a2 b3 c5/2d–2. The percentage error in the measurement of a, b, c and d are 1%, 2%, 3% and 4%, respectively. What is the percentage error in quantity X? If the value of X calculated on the basis of the above relation is 2.763, to what value should you round off the result.
If E, L, M, and G denote the quantities as energy, angular momentum, mass, and constant of gravitation respectively, then the dimensions of P in the formula P = EL2M−5G−2 are ______.
A travelling microscope has 20 divisions per cm on the main scale while its Vernier scale has total 50 divisions and 25 Vernier scale divisions are equal to 24 main scale divisions, what is the least count of the travelling microscope?
A travelling microscope is used to determine the refractive index of a glass slab. If 40 divisions are there in 1 cm on main scale and 50 Vernier scale divisions are equal to 49 main scale divisions, then least count of the travelling microscope is ______ × 10-6 m.
If the zero of the vernier lies on the right-hand side and the fourth division coincides with the main scale division when the jaws are in contact so the correction will be ______.
What are random errors?
A student reads a measuring cylinder from above the liquid level, causing the reading to be higher than the actual value. What type of error is this?
If the pointer of the voltmeter is not exactly at the zero of the scale, then the error is called ______.
Zero error of an instrument introduces ______.
Constant error can be caused due to ______.
