Advertisements
Advertisements
प्रश्न
A circuit containing a 80 mH inductor and a 60 µF capacitor in series is connected to a 230 V, 50 Hz supply. The resistance of the circuit is negligible.
(a) Obtain the current amplitude and rms values.
(b) Obtain the rms values of potential drops across each element.
(c) What is the average power transferred to the inductor?
(d) What is the average power transferred to the capacitor?
(e) What is the total average power absorbed by the circuit?
[‘Average’ implies ‘averaged over one cycle’.]
Advertisements
उत्तर
Inductance, L = 80 mH = 80 × 10−3 H
Capacitance, C = 60 μF = 60 × 10−6 F
Supply voltage, V = 230 V
Frequency, v = 50 Hz
Angular frequency, ω = 2πv = 100 π rad/s
Peak voltage, V0 = `"V" sqrt2 = 230 sqrt2 "V"`
(a) Maximum current is given as:
I0 = `"V"_0/((ω"L" - 1/(ω"C")))`
= `(230 sqrt3)/((100π xx 80 xx 10^-3 - 1/(100π xx 60 xx 10^-6)))`
= `(230 sqrt2)/((8π - 1000/(6π)))`
= −11.63 A
The negative sign appears because `ω"L" < 1/(ω"C")`.
Amplitude of maximum current, |I0| = 11.63 A
Hence, rms value of current, I = `"I"_0/sqrt2 = (-11.63)/sqrt2` = −8.22 A
(b) Potential difference across the inductor,
VL = I × ωL
= 8.22 × 100 π × 80 × 10−3
= 206.61 V
Potential difference across the capacitor,
Ve = `"I" xx 1/(ω"C")`
= `8.22 xx 1/(100π xx 60 xx 10^-6)`
= 436.3 V
(c) Average power consumed by the inductor is zero as actual voltage leads the current by `π/2`.
(d) Average power consumed by the capacitor is zero as voltage lags current by `π/2`.
(e) The total power absorbed (averaged over one cycle) is zero.
संबंधित प्रश्न
A device X is connected across an ac source of voltage V = V0 sin ωt. The current through X is given as
`I = I_0 sin (omega t + pi/2 )`
1) Identify the device X and write the expression for its reactance.
2) Draw graphs showing the variation of voltage and current with time over one cycle of ac, for X.
3) How does the reactance of the device X vary with the frequency of the ac? Show this variation graphically.
4) Draw the phasor diagram for the device X.
In a series LCR circuit connected to an ac source of variable frequency and voltage ν = vm sin ωt, draw a plot showing the variation of current (I) with angular frequency (ω) for two different values of resistance R1 and R2 (R1 > R2). Write the condition under which the phenomenon of resonance occurs. For which value of the resistance out of the two curves, a sharper resonance is produced? Define Q-factor of the circuit and give its significance.
The voltage and current in a series AC circuit are given by V = V0cos ωt and i = i0 sin ωt. What is the power dissipated in the circuit?
Two alternating currents are given by `i_1 = i_0 sin wt and i_2 = i_0 sin (wt + pi/3)` Will the rms values of the currents be equal or different?
Can the peak voltage across the inductor be greater than the peak voltage of the source in an LCR circuit?
Can a hot-wire ammeter be used to measure a direct current of constant value? Do we have to change the graduations?
An alternating current of peak value 14 A is used to heat a metal wire. To produce the same heating effect, a constant current i can be used, where i is
A constant current of 2.8 A exists in a resistor. The rms current is
The peak power consumed by a resistive coil, when connected to an AC source, is 80 W. Find the energy consumed by the coil in 100 seconds, which is many times larger than the time period of the source.
The dielectric strength of air is 3.0 × 106 V/m. A parallel-plate air-capacitor has area 20 cm2 and plate separation 0.10 mm. Find the maximum rms voltage of an AC source that can be safely connected to this capacitor.
A coil of inductance 5.0 mH and negligible resistance is connected to the oscillator of the previous problem. Find the peak currents in the circuit for ω = 100 s−1, 500 s−1, 1000 s−1.
A resistor of resistance 100 Ω is connected to an AC source ε = (12 V) sin (250 π s−1)t. Find the energy dissipated as heat during t = 0 to t = 1.0 ms.
A small town with a demand of 800 kW of electric power at 220 V is situated 15 km away from an electric plant generating power at 440 V. The resistance of the two wire line carrying power is 0.5 Ω per km. The town gets power from the line through a 4000-220 V step-down transformer at a sub-station in the town.
(a) Estimate the line power loss in the form of heat.
(b) How much power must the plant supply, assuming there is negligible power loss due to leakage?
(c) Characterise the step up transformer at the plant.
Phase diffn between voltage and current in a capacitor in A.C Circuit is.
The output of a step-down transformer is measured to be 24 V when connected to a 12-watt light bulb. The value of the peak current is ______.
RMS value of an alternating current flowing in a circuit is 5A. Calculate its peak value.
In the Figure below, the current-voltage graphs for a conductor are given at two different temperatures, T1 and T2.
- At which temperature T1 or T2 is the resistance higher?
- Which temperature (T1 or T2) is higher?
